From Tape Measures and Concrete Sanders to Lasers and Automation

When Skill Meant Making It Fit When I first started on a roof truss factory floor at 15, every piece of timber...

July 27, 2026

From Tape Measures and Concrete Sanders to Lasers and Automation

When Skill Meant Making It Fit

When I first started on a roof truss factory floor at 15, every piece of timber was measured with a tape and saw angles were set against a giant protractor. Half-degrees were selected by eye.

The sawyers were big, burly men who could choose those angles without dropping the cigarette permanently attached to the corner of the mouth. More impressive was their ability to read a ten-year-old tape measure on which barely any numbers remained.

Factory nicknames were an education of their own. The boss was “Noodles” because he thought everything could be done in two minutes. “Bottle” was empty from the neck up, and “Lightning” never hit the same spot twice with a hammer. The nicknames were rarely selected by the person receiving them, and there did not appear to be a formal appeals process.

Variation was part of the process, so the jig setter’s skill was making everything fit. If a member was a few millimetres long, the concrete sander came out: one carefully judged bang on the factory floor. Too gentle, nothing happened. Too enthusiastic, the member became too short.

Traditional methods produced very good roof trusses, but consistency depended heavily on the knowledge and judgement of individual sawyers and jig setters.

The Saw Now Fetches Its Own Timber

Modern saws receive cutting information electronically from the design software. They can retrieve timber from an automated pack-feeding system, scan it to identify the bow, orientate it correctly, cut it to the programmed length and angle, and label the finished component – all without direct human interaction during the normal production sequence.

The operator still monitors quality and steps in when timber or machinery behaves unexpectedly. The difference is that the process no longer relies on half-degree estimates or a tape measure whose numbers disappeared years ago.

From Manual Jigs to Projected Designs

Automated pucks move into position from the truss design, creating a repeatable physical template. Laser projection displays the truss profile and connector-plate locations at full size over the jigging station, helping operators compare timber, jigging and plate positions directly with the design. When several trusses of the same type are manufactured, each is assembled against the same jigging arrangement.

The design is no longer confined to a drawing or cutting list. It is displayed at full size over the truss while it is being assembled.

Wall frames may look straightforward, but modern designs can include different wall heights, large openings, engineered lintels, bracing and tie-down requirements. Our framing line, including the Component Master, prepares accurately cut and clearly identified components before assembly, reducing adjustments and improving consistency between frames.

The Skill Changed – It Didn’t Disappear

Automation does not eliminate skilled people. Timber still bows, twists, springs and contains defects. Operators must understand the material, monitor the machinery and recognise when something is not right.

The skill once involved reading worn tapes, manually setting saw angles and knowing exactly how hard to apply the concrete sander. Today it involves digital production information, automated equipment and quality control.

The best results come from combining the repeatability of modern equipment with operators who understand timber and recognise when something does not look right.

What It Means for Builders

Greater manufacturing consistency can make prefabricated elements more predictable during installation and can mean:

  • More uniform roof truss profiles.
  • More consistent wall frame dimensions.
  • Accurate component and joint locations.
  • More consistent connector-plate positioning.
  • Fewer avoidable adjustments during installation.

Automation cannot control slab tolerances, site conditions, handling or installation. What it can do is reduce unnecessary manufacturing variation before the product reaches site.

The objective remains the same: manufacture roof trusses and wall frames that match the design and fit together properly.

Sign Up

Cash Account

Sign up to our Cash Account where you receive benefits. This account type is subject to 50% deposit on order placement, and balance prior to delivery. Once you sign up we will get your account up and running, usually by the next business day.

Sign Up

30-Day Account

Apply for a NewTruss trade account and benefit from convenient 30-day payment terms, helping you keep your projects moving.

What are you searching for?